PENGARUH ISIAN PADA BIDANG DISKONTINU TERHADAP PARAMETER KUAT GESER BATU TUFF DI KECAMATAN PLERET, KABUPATEN BANTUL, PROVINSI DAERAH ISTIMEWA YOGYAKARTA

RUTINAH, AMELIA DEWI (2013) PENGARUH ISIAN PADA BIDANG DISKONTINU TERHADAP PARAMETER KUAT GESER BATU TUFF DI KECAMATAN PLERET, KABUPATEN BANTUL, PROVINSI DAERAH ISTIMEWA YOGYAKARTA. Other thesis, UPN "Veteran" Yogyakarta.

[thumbnail of RINGKASAN.pdf]
Preview
Text
RINGKASAN.pdf

Download (47kB) | Preview

Abstract

RINGKASAN
Pada umumnya, conto batuan yang diuji di laboratorium berukuran kecil dan
tidak mengandung retakan dan dianggap bersifat homogen, isotrop dan kontinu. Pada
kenyataannya bidang diskontinuitas berupa rekahan kerap ditemui pada batuan.
Keberadaan diskontinuitas ini akan mengubah perilaku batuan apabila diberi
pembebanan. Permasalahan yang kerap muncul adalah rekahan yang terisi oleh
material lain kemudian menyebabkan ketidakstabilan lereng bahkan menginisiasi
terjadinya kelongsoran. Berdasarkan hal tersebut perlu diketahui berapa besar
pengaruh dan penurunan nilai kuat geser batuan akibat pengaruh isian.
Sampel penelitian berupa batu Tuff diambil dari Kecamatan Pleret, Kabupaten
Bantul, Provinsi D.I. Yogyakarta. Pengujian dilakukan pada conto yang telah
dipatahkan kemudian bidang patahan diisi dengan material isian berupa Wackestone
dengan ketebalan 0,25 dan 0,5 dari amplitudo batuan. Hasil pengujian geser langsung
dianalisis dengan menggunakan criteria Mohr-Coulomb (1773) dan Barton (1973).
Berdasarkan hasil pengujian, diketahui bahwa nilai kohesi batuan turun
78,92% untuk tebal isian 0,25 amplitudo dan 89,19% untuk isian 0,5 amplitudo.
Sedangkan nilai sudut gesek turun berkisar 32% untuk conto dengan isian 0,25 dan
0,5 amplitudo. Penurunan nilai kohesi dan sudut gesek dalam ini dikarenakan saat
pergeseran berlangsung permukaan geser batuan tertutup oleh material pengisi. Selain
itu, permukaan geser tidak terlalu kasar sehingga undulasi batuan tidak berperan
banyak saat proses pergeseran. Untuk meyakinkan bahwa parameter kuat geser
mempengaruhi kestabilan lereng, maka dimodelkan jenjang dengan tinggi jenjang
10m dan kemiringan 75°. Keberadaan isian mempengaruhi faktor keamanan lereng
sehingga terjadi penurunan faktor keamanan yang cukup besar untuk kondisi, batuan
terisi dengan ketebalan 0,25 dari amplitudo sebesar 78% dan 87,65% untuk kondisi
batuan dengan tebal isian 0,5 dari amplitudo.

ABSTRACT
Generally, rock sample that is tested in laboratory is small and massive. The
sample also assumed as homogeneous, isotopric and continuous.In fact, discontinuity
such as joint often encountered in rock mass. The presence of discontinuity will
change the behavior of rock mass . This situation become worst when the joint is
filled by infilling material. Filled joint poses a number of design and constructional
problem that may influence the stability. Based on that problem, how much are the
effect and reduction of shear strength caused by filled joint needed to know.
The sample is classified as Tuff that is taken from, Pleret, Bantul,
D.I.Yogyakarta. The test was conducted on residual sample that is filled by
Wackestone (Dunham, 1962). The thickness of infilling material is 0,25 and 0,5 from
the rock amplitude. The result of the test is analyzed with some criterion which are
Mohr-Coulomb (1773) and Barton (1973).
Based on the research, there are 3 conclusions. Cohesion will be decreased by
73,63% and 86,91% for the sample with infilling material thickness 0,25 and 0,5
from the amplitude. In the other hand, friction angle is decreased 42,53% for sample
with infilling material’s thickness 0,25 amplitude and 41,93% for sample with
infilling material’s thickness 0,5 from amplitude. That condition is occurred because
the shear surface is covered by infilling material. Moreover, the asperities of the shear
surface is not really rough so it was not much affect the shear process. To convince
that cohesion and friction angle are affect the slope stability, a single bench is
modeled with height 10m and single slope 75°. The presence of infilling material
affect the factor of safety 71,08% and 83,53% for 0,25 and 0,5 thickness infilling
material from the amplitude.

Item Type: Thesis (Other)
Subjek: T Technology > TN Mining engineering. Metallurgy
Divisions: x. Faculty of Engineering, Science and Mathematics > School of Civil Engineering and the Environment
Depositing User: Ratna Sufiatin
Date Deposited: 10 Oct 2016 06:34
Last Modified: 10 Oct 2016 06:34
URI: http://eprints.upnyk.ac.id/id/eprint/7481

Actions (login required)

View Item View Item