KAJIAN TEKNIS PENGEBORAN DAN PELEDAKAN OVERBURDEN DI TAMBANG BATUBARA PT. THIESS CONTRACTORS INDONESIA SITE SENAKIN KALIMANTAN SELATAN

ANNAS, MERZA (2013) KAJIAN TEKNIS PENGEBORAN DAN PELEDAKAN OVERBURDEN DI TAMBANG BATUBARA PT. THIESS CONTRACTORS INDONESIA SITE SENAKIN KALIMANTAN SELATAN. Other thesis, UPN ''VETERAN'' YOGYAKARTA.

[thumbnail of RINGKASA1.pdf]
Preview
Text
RINGKASA1.pdf

Download (76kB) | Preview
[thumbnail of Daftar isi.pdf]
Preview
Text
Daftar isi.pdf

Download (80kB) | Preview
[thumbnail of Daftar Gambar.pdf]
Preview
Text
Daftar Gambar.pdf

Download (64kB) | Preview
[thumbnail of Daftar Lampiran.pdf]
Preview
Text
Daftar Lampiran.pdf

Download (57kB) | Preview
[thumbnail of Daftar Tabel.pdf]
Preview
Text
Daftar Tabel.pdf

Download (60kB) | Preview

Abstract

Salah satu kegiatan penambangan yang dilakukan oleh PT. Thiess
Contractors Indonesia adalah pembongkaran overburden dengan target produksi
bulanan sekitar 3.400.000 bcm. Target produksi tersebut 90% dilakukan dengan
menggunakan kegiatan pengeboran dan peledakan.
Hasil pengamatan di lapangan mendapati bahwa pengeboran lubang ledak
menggunakan pola paralel, sedangkan geometri peledakan untuk batulempung
dan batupasir adalah kedalaman 17 m, subdrilling 2m, dan stemming 5 m.
Perbedaanya terletak pada burden dan spasinya. Batupasir mempunyai burden 7,5
m spasi 7,5 m, sedangkan batulempung mempunyai burden 10 m spasi 10 m.
Analisis hasil peledakan pada batupasir dan batulempung menggunakan
metode Kuz-ram mendapatkan nilai prosentase boulder (80 cm) batupasir sebesar
17,94% dan 12,06% pada batulempung. Prosentase boulder aktual berdasarkan
analisis menggunakan Split-dekstop sebesar 6,5% pada batpasir dan 0% pada
batulempung.
Produktifitas alat gali Back Hoe Liebherr R 994 B mempunyai target 1050
bcm/jam. Produktifitas tersebut tercapai pada penggalian batulempung tetapi tidak
tercapai pada batupasir.
Penyebab tidak tercapainya produktifitas alat gali adalah rata – rata jumlah
swing load yang besar. Hal itu disebabkan oleh deviasi pengeboran yang besar.
Deviasi pengeboran yang besar mengakibatkan terdapatnya banyak boulder yang
menyulitkan untuk digali.
Persen boulder aktual pada batupasir dan batulempung tidak bermasalah,
sehingga tidak perlu merubah geometri peledakan, namun disarankan untuk
meninkatkan presisi pengeboran pada batupasir dengan cara meningkatkan
kerjasama antara helper drilling dengan operator drilling atau menurunkan target
produksi pada penggalian batupasir.

One of the mining activities carried out by PT. Thiess Contractors
Indonesia is the dismantling of overburden with a monthly production target of
around 3.4 million bcm. Target production is 90% done using drilling and blasting
activities.
Observations in the field found that drilling explosive holes using parallel
patterns, while blasting geometry for mudstone and sandstone is the depth of 17
m, 2m subdrilling and stemming 5 m. The difference lies in the burden and
spaces. Sandstone has a burden of 7.5 m spacing of 7.5 m, while the mudstone has
burden of 10 m, spacing 10 m.
Analysis of the results of blasting the sandstone and mudstone use Kuzram
method to get the value of the percentage of boulder (80 cm) sandstone is
17.94% and 12.06% in mudstone. Percentage of actual boulder based analysis
using Split-desktop by 6.5% in sandstones and 0% in mudstone.
Productivity digging tools Back Hoe Liebherr R 994 B has a target of
1050 bcm / hour. Productivity was reached on extracting mudstone but not
reached in sandstones
The cause of the failure of productivity digging tools are, the average
number of bucket / large vessel. It was caused by drilling a large deviation.
Drilling a large deviation leading to a large boulder which makes it difficult for
many excavated.
Actual Percent sandstone boulder mudstone no problem, so no need to
change the geometry of the explosion, but it is recommended to increase the
precision drilling in sandstone by increasing cooperation between helper drilling
with drilling operators or lower the production target on sandstone digging.

Item Type: Thesis (Other)
Subjek: T Technology > TN Mining engineering. Metallurgy
Divisions: x. Faculty of Engineering, Science and Mathematics > School of Engineering Sciences
Depositing User: Erny Azyanti
Date Deposited: 26 May 2016 06:35
Last Modified: 26 May 2016 06:35
URI: http://eprints.upnyk.ac.id/id/eprint/2570

Actions (login required)

View Item View Item