ANALISIS KESTABILAN LERENG DENGAN MENGGUNAKAN METODE KESETIMBANGAN BATAS DAN PENDEKATAN PROBABILITAS KUARI ANDESIT CV.TRIKARYA DESA KALIREJO KECAMATAN KOKAP KABUPATEN KULON PROGO D.I. YOGYAKARTA

MULYA, REINARD DEO HAGA (2019) ANALISIS KESTABILAN LERENG DENGAN MENGGUNAKAN METODE KESETIMBANGAN BATAS DAN PENDEKATAN PROBABILITAS KUARI ANDESIT CV.TRIKARYA DESA KALIREJO KECAMATAN KOKAP KABUPATEN KULON PROGO D.I. YOGYAKARTA. Other thesis, Universitas Pembangunan Nasional Veteran Yogyakarta.

[thumbnail of COVER.pdf]
Preview
Text
COVER.pdf

Download (24kB) | Preview
[thumbnail of PENGESAHAN.pdf]
Preview
Text
PENGESAHAN.pdf

Download (176kB) | Preview
[thumbnail of DAFTAR ISI.pdf]
Preview
Text
DAFTAR ISI.pdf

Download (168kB) | Preview
[thumbnail of ABSTRAK.pdf]
Preview
Text
ABSTRAK.pdf

Download (29kB) | Preview

Abstract

CV. Trikarya adalah perusahaan pertambangan andesit yang terletak di Desa
Kalirejo, Kecamatan Kokap, Kabupaten Kulon Progo Provinsi D.I. Yogyakarta.
Sistem penambangan menggunakan sistem tambang terbuka metode kuari. Saat ini
tinggi lereng akhir penambangan yang diterapkan adalah 20 meter dengan
kemiringan 56o. Andesit di lereng ini masih dapat dimungkinkan kembali untuk
ditambang, sehingga tinggi lereng dan kemiringan lereng saat ini masih dapat
dilakukan optimalisasi. Kemudian pada lokasi yang sama, yaitu di sebelah selatan
dari lereng terdapat andesit yang dapat ditambang, sehingga diperlukan geometri
lereng yang aman. Analisis kestabilan lereng ini bertujuan untuk mengetahui
mantap tidaknya lereng akhir yang diterapkan. Potensi longsoran diketahui dengan
menggunakan metode kinematik. Analisis kestabilan lereng menggunakan metode
kesetimbangan batas. Parameter nilai kekuatan massa batuan berbeda-beda,
sehingga penyelesaian dari ketidakpastian tersebut dilakukan juga analisis
probabilitas. Parameter kekuatan massa batuan ini adalah mb, s, a, GSI, kohesi, dan
sudut gesek dalam. Adapun untuk menentukan mantap atau tidaknya lereng
digunakan kriteria keruntuhan Mohr-Coloumb. Metode sampling dengan
menggunakan metode Monte Carlo 500 sampling. Pengolahan data statistik
dilakukan pada bobot isi, spasi kekar, dip/dip direction kekar, kohesi, dan sudut
gesek dalam. Hasil analisis kestabilan lereng diperoleh nilai Faktor keamanan (FK)
dan Probabilitas Longsor (PL). Acuan standar lereng stabil adalah FK>1,1 dan
PL25-50%.
Hasil penelitian menunjukkan adanya pengaruh nilai kekuatan batuan (UCS)
terhadap parameter kekuatan massa batuan mb, s, a, kohesi, dan sudut gesek dalam.
Longsoran yang berpotensi adalah baji, bidang, dan topling. Kestabilan lereng
dipengaruhi oleh tinggi lereng dan kemiringan lereng. Hasil analisis kestabilan
lereng ini diperoleh alternatif geometri lereng dengan asumsi kondisi muka air
tanah kering. Hasil analisis longsoran baji adalah aman dengan tinggi lereng sampai
30 m dengan kemiringan 89°. Hasil analisis longsoran bidang didapatkan alternatif
geometri lereng dengan kemiringan 89° dan tinggi 25 m nilai FK 1,14 dan PL
14,2%. Hasil analisis longsoran topling didapatkan alternatif geometri lereng
dengan kemiringan 83°, tinggi 20 m nilai FK 1,35 dan PL 34,5%; kemiringan 86°,
tinggi 15 m nilai FK 1,27 dan PL 31,8%; kemiringan 89°, tinggi 15 m nilai FK 1,20
dan PL 33,3%
Kata kunci :metode kesetimbangan batas, kekuatan massa batuan, faktor
keamanan, probabilitas longsor
vi
ABSTRACT
CV. Trikarya is an andesite mining company located in Kalirejo Village,
Kokap District, Kulon Progo Regency, Province of D.I. Yogyakarta. The mining
system uses open pit mining system quarry method. Andesites on this slope can still
be possible to be mined again, so that the current slope height and slope can still be
optimized. Then at the same location, which is to the south of the slope, there is an
andesite that can be mined, so that a safe slope geometry is needed. The slope
stability analysis is performed to assess the safety factors of the final slope. The
potential failure of a slope will be discovered by using the stereonet method. Limit
equilibrium method is used for the slope stability analysis. Various parameters are
available for the rock mass strength, therefore probability analysis will also be used
to analyze the uncertainties of the mass strength. These rock mass strength
parameters are mb, s, a, GSI, cohesion, and friction angle. Mohr-Coloumb failure
criteria is used to determine whether or not the slopes are stable. Monte Carlo
method 500 samples is used for the sampling method. Statistical data processing
was carried out on unit weight, joint spacing, dip / dip direction, cohesion, and
friction angle. The results of slope stability analysis obtained the value of factor of
safety (FoS) and Probability of failure (PoF). The standard reference for stable
slopes is FK> 1.1 and PoF 25-50%.
The results showed the influence of rock strength values (UCS) on the
strength parameters of rock mass mb, s, a, cohesion, and friction angle. Potential
failures are wedges, plane, and toppling. Slope stability is influenced by slope
height and slope. The results of this slope stability analysis obtained alternative
slope geometry assuming dry groundwater conditions. The results of the wedge
failure analysis are safe with a slope height of up to 30 m with a slope of 89 °. The
results of plane failure analysis found an alternative slope geometry with a slope of
89 °, a height of 25 m, FoS 1.14 and PoF 14,2%. The results of toppling failure
analysis found an alternative slope geometry with a slope of 83 °, a height of 20 m
FoS value 1.35 and PoF 34,5%. slope of 86 °, height of 15 m, FoS value 1.27 and
PoF 31,8%. slope 89 °, height 15 m FoS value 1.20 and PoF 33,3%
Keywords: limit equilibrium method, rock mass strength, safety factor, probability
of failure

Item Type: Thesis (Other)
Subjek: T Technology > T Technology (General)
Divisions: x. Faculty of Engineering, Science and Mathematics > School of Engineering Sciences
Depositing User: Sarimin Sarimin
Date Deposited: 20 Aug 2019 02:14
Last Modified: 20 Aug 2019 02:14
URI: http://eprints.upnyk.ac.id/id/eprint/20771

Actions (login required)

View Item View Item